6x10 Shed Material List

Quick Answer

A 6x10 gable shed with 8 ft walls, 16 inch on center framing, 4/12 roof pitch, pressure treated floor framing, OSB or plywood sheathing, a basic single door, and gravel foundation is a compact storage structure. This size is commonly used for garden tools, bicycles, trash bins, and small equipment where space is limited.

See all shed material lists by size

You will need:

• Pressure treated lumber for the floor system
• 2x4 wall framing
• 2x4 or 2x6 roof framing
• Floor, wall, and roof sheathing
• Panel or lap siding
• Asphalt shingles and underlayment
• Basic door framing materials
• Standard fasteners and hardware

In 2026 pricing, expect a realistic total material cost of: $1,400 to $2,400

This assumes a gravel base and basic exterior finishes only.

Need a smaller option? See our 6x6 shed material list. Need more storage space? See our 6x12 shed material list.

Full Material List

Quantities assume 8 ft wall height, 16 inch on center spacing, and one standard single door opening.

Floor Framing

A 6 ft span allows lighter framing while maintaining adequate strength.

Gravel Base

• 1.5 to 2.5 cubic yards of compacted 3/4 inch crushed gravel

Floor Frame (Pressure Treated)

Perimeter

• 2x6x10 PT – 2 (long rim joists)
• 2x6x6 PT – 2 (end band joists)

Floor Joists (16 inch OC across 6 ft span)

• 2x6x6 PT – 6 to 7

Floor Sheathing

• 3/4 inch tongue and groove plywood or OSB – 2 sheets

Fasteners

• Exterior screws or galvanized framing nails
• Joist hangers optional but recommended

Wall Framing

Framed 16 inch on center.

• 2x4x8 studs
• 40 to 50 total
• Includes perimeter walls
• Door framing
• Waste allowance

Plates

• 2x4x10 – 6 (long walls, double top plates + bottom plates)
• 2x4x6 – 6 (end walls)

Door Framing

• 2x6x8 – 2 (header material)
• 1/2 inch plywood spacer
• Jack studs included in stud count

Roof Framing

Short span allows lighter rafters.

Rafters (4/12 pitch, 16 inch OC)

• 2x4x8 or 2x6x8 – 14 to 16

Approximately 7 to 8 rafter pairs.

Ridge Board

• 2x6x10 – 1

Collar Ties or Ceiling Ties

• 2x4x6 – 7 to 8

Sheathing

Wall Sheathing

• 7/16 inch OSB or plywood – 7 to 9 sheets

Panel siding may eliminate separate sheathing.

Roof Sheathing

• 7/16 inch OSB or plywood – 4 to 5 sheets

Siding

Panel siding is the most common choice for small sheds.

T1-11 or LP SmartSide Panels

• 7 to 9 sheets

Alternative siding systems require additional trim and backing materials.

Roofing

Underlayment

• 1 roll synthetic underlayment

Drip Edge

• 5 to 6 pieces (10 ft lengths)

Shingles

• Approximately 1 square
• 3 to 4 bundles depending on waste

Roofing Nails

• 2 to 3 lb box

Hardware and Fasteners

• 16d framing nails or structural screws
• 8d nails for sheathing
• Exterior construction screws
• Construction adhesive (1 to 2 tubes)
• 2 to 3 heavy-duty door hinges
• Exterior latch or handle
• Lockset or padlock hardware
• Flashing for door header

Estimated Cost Breakdown

Typical 2026 pricing ranges.

• Gravel Base: $120 to $250
• Pressure Treated Floor Framing: $250 to $450
• Wall Framing Lumber: $300 to $550
• Roof Framing Lumber: $200 to $400
• Sheathing (walls and roof): $400 to $700
• Siding: T1-11: $300 to $550; LP SmartSide: $550 to $900; Vinyl system: $700 to $1,200
• Roofing: $150 to $350
• Hardware and Fasteners: $80 to $200

Total Estimated Range

With basic panel siding: $1,400 to $1,900

With upgraded siding: $1,900 to $2,400

Costs remain moderate due to:

• Small floor area (60 sq ft)
• Minimal framing requirements
• Limited roofing coverage
• Fixed costs for hardware still present
• Regional lumber prices can affect totals

If you want exact cut diagrams, printable framing layouts, and step-by-step blueprints for this 6x10 shed, detailed plans eliminate guesswork and reduce lumber waste.

Get the Complete 6x10 Shed Plans Here

Tools Required

Standard homeowner tools are sufficient.

Essential tools:

• Circular saw
• Drill and impact driver
• Hammer
• Level
• Speed square
• Tape measure
• Chalk line
• Ladder
• Shovel and rake
• Hand tamper

Helpful tools:

• Miter saw
• Framing nailer
• Sawhorses

Most homeowners can build this size alone or with minimal help.

Step-by-Step Build Overview

High-level sequence only.

• Prepare and compact gravel base.
• Build pressure treated floor frame and verify square.
• Install floor sheathing.
• Frame walls on the ground including door opening.
• Raise walls, plumb, and brace.
• Install double top plates.
• Install ridge board and rafters.
• Add collar ties or ceiling ties.
• Install roof sheathing.
• Install drip edge and underlayment.
• Install shingles.
• Install wall sheathing if required.
• Install siding.
• Build and hang door.
• Install trim and hardware.
• Check alignment during construction to ensure proper door fit.

Common Mistakes

• Poor base preparation. Causes settling and door alignment issues.
• Using untreated lumber near the ground. Leads to premature rot.
• Underestimating material quantities. Results in delays and extra trips.
• Weak door framing. Causes sagging or sticking doors.
• Insufficient anchoring in windy areas. Lightweight structures can shift.
• Skipping wall bracing during construction. Walls may move before roof installation.

Is It Worth Building Yourself?

DIY material cost: $1,400 to $2,400

Typical prebuilt 6x10 shed delivered in 2026: $2,500 to $4,500

DIY savings typically range from $1,000 to $2,500.

Consider:

• Build time of roughly 1 to 2 days
• Easy material handling
• Low construction risk
• Possible permit requirements depending on location

For most homeowners, building this size shed yourself is practical and cost-effective.

Get Exact Cut Diagrams and Printable Plans

This material list provides realistic quantities and cost expectations for a 6x10 shed.

It does not include:

• Exact rafter angle calculations
• Detailed wall framing layouts
• Header sizing diagrams
• Precise overhang dimensions
• Optimized cut lists
• Printable construction diagrams

Detailed blueprints with exact measurements, framing layouts, and printable cut sheets simplify construction, reduce waste, and help ensure structural accuracy.

For a one-time build, complete plans typically save time and prevent costly mistakes during construction.

Get the Complete 6x10 Shed Plans Here