10x24 Shed Material List
Quick Answer
A 10x24 gable shed with 8 ft walls, 16 inch on center framing, 4/12 roof pitch, pressure treated floor framing, OSB or plywood sheathing, a basic double door, and gravel foundation is a long, narrow structure commonly used for equipment storage, workshop space, motorcycles, or garage overflow. The extended 24 ft length increases material quantities significantly even though the 10 ft width remains manageable.
See all shed material lists by size
You will need:
- Pressure treated lumber for the floor system
- 2x4 wall framing
- 2x6 roof framing
- Extensive floor, wall, and roof sheathing
- Panel or lap siding
- Asphalt shingles and underlayment
- Reinforced door framing
- Large quantities of fasteners and hardware
In 2026 pricing, expect a realistic total material cost of: $4,200 to $6,800
This assumes a gravel base and basic exterior finishes only.
Need a smaller option? See our 12x20 shed material list. Want more space? See our 14x18 shed material list.
Full Material List
Quantities assume 8 ft wall height, 16 inch on center spacing, and a standard double door on one gable end.
Floor Framing
A 10 ft span is moderate, but the 24 ft length requires many joists.
Gravel Base
- 6 to 8 cubic yards of compacted 3/4 inch crushed gravel
Floor Frame (Pressure Treated)
Perimeter
- 2x8x24 PT – 2 (long rim joists)
- 2x8x10 PT – 2 (end band joists)
If 24 ft boards are unavailable, splice sections over blocking.
Floor Joists (16 inch OC across 10 ft span)
- 2x8x10 PT – 18 to 20
Floor Sheathing
- 3/4 inch tongue and groove plywood or OSB – 8 sheets
Fasteners
- Exterior-rated screws or galvanized framing nails
- Joist hangers recommended
Wall Framing
Framed 16 inch on center.
- 2x4x8 studs
- 120 to 140 total
- Includes perimeter walls
- Additional studs for corners and door framing
- Waste allowance
Plates
- 2x4x24 – 6 (long walls, double top plates + bottom plates)
- 2x4x10 – 6 (end walls)
Splicing shorter boards is common for long walls.
Double Door Framing
Typical opening: 60 to 72 inches wide.
- 2x8x8 – 2 (header material)
- 1/2 inch plywood spacer
- Jack and king studs included in stud count
Roof Framing
A 10 ft span allows moderate rafters across a long ridge.
Rafters (4/12 pitch, 16 inch OC)
- 2x6x14 – 36 to 40
Approximately 18 to 20 rafter pairs.
Ridge Board
- 2x8x24 – 1
Collar Ties or Ceiling Joists
- 2x4x10 – 18 to 20
Sheathing
Long walls significantly increase sheet usage.
Wall Sheathing
- 7/16 inch OSB or plywood – 22 to 26 sheets
Panel siding may eliminate separate sheathing.
Roof Sheathing
- 7/16 inch OSB or plywood – 12 to 14 sheets
Siding
Panel siding is most common for structures of this size.
T1-11 or LP SmartSide Panels
- 22 to 26 sheets
Vinyl or lap siding systems require additional trim and accessories.
Roofing
Underlayment
- 2 rolls synthetic underlayment
Drip Edge
- 10 to 12 pieces (10 ft lengths)
Shingles
- Approximately 3 squares
- 9 to 12 bundles depending on waste
Roofing Nails
- 8 to 10 lb box
Hardware and Fasteners
- 16d framing nails or structural screws
- 8d nails for sheathing
- Exterior construction screws
- Construction adhesive (4 to 6 tubes)
- Hurricane ties recommended
- Heavy-duty hinges (3 per door)
- Exterior double-door latch or lockset
- Padlock hardware
- Flashing for door header
Estimated Cost Breakdown
Typical 2026 pricing ranges.
- Gravel Base: $300 to $650
- Pressure Treated Floor Framing: $800 to $1,400
- Wall Framing Lumber: $800 to $1,300
- Roof Framing Lumber: $600 to $1,000
- Sheathing (walls and roof): $1,200 to $1,900
- Siding: T1-11: $900 to $1,400; LP SmartSide: $1,600 to $2,500; Vinyl system: $2,200 to $3,400
- Roofing: $600 to $1,000
- Hardware and Fasteners: $250 to $450
Total Estimated Range
With basic panel siding: $4,200 to $5,500
With upgraded siding: $5,500 to $6,800
Costs increase primarily due to:
- Long 24 ft wall runs
- High stud count
- Large sheathing quantities
- Extended roof area
- Reinforced door framing
- Increased fastener usage
- Transportation costs may increase due to long lumber lengths
If you want exact cut diagrams, printable framing layouts, and step-by-step blueprints for this 10x24 shed, detailed plans eliminate guesswork and reduce lumber waste.
Get the Complete 10x24 Shed Plans Here
Tools Required
Standard framing tools with enough workspace for long components.
Essential tools:
- Circular saw
- Miter saw
- Drill and impact driver
- Framing hammer
- Level
- Speed square
- Tape measure
- Chalk line
- Ladders
- Shovel and rake
- Plate compactor or heavy hand tamper
Helpful tools:
- Pneumatic framing nailer
- Roofing nailer
- Laser level
- Sawhorses
- Clamps
Assistance is helpful but not always required.
Step-by-Step Build Overview
High-level sequence only.
- Prepare and compact gravel base across entire footprint.
- Build pressure treated floor frame and verify square.
- Install floor sheathing.
- Frame walls on the ground including double door opening.
- Raise walls, plumb, and brace securely.
- Install double top plates tying walls together.
- Install ridge board and rafters.
- Add collar ties or ceiling joists.
- Install roof sheathing.
- Install drip edge and underlayment.
- Install shingles.
- Install wall sheathing if required.
- Install siding.
- Build and hang double doors.
- Install trim and hardware.
- Check for square frequently on long structures to prevent alignment problems.
Common Mistakes
- Not maintaining square across long walls. Small errors compound over distance.
- Using undersized floor joists for equipment loads. Leads to flex or sagging.
- Poor base preparation. Causes uneven settling.
- Underestimating materials. Leads to delays and extra trips.
- Weak double-door framing. Causes sagging or misalignment.
- Inadequate bracing during construction. Long walls can shift easily.
Is It Worth Building Yourself?
DIY material cost: $4,200 to $6,800
Typical prebuilt 10x24 shed delivered in 2026: $7,500 to $13,000
DIY savings typically range from $3,000 to $7,000.
Consider:
- Build time of roughly 4 to 6 days
- Handling long materials
- Need for accurate layout
- Possible permit requirements
For homeowners comfortable with construction tasks, building yourself is usually financially worthwhile.
Get Exact Cut Diagrams and Printable Plans
This material list provides realistic quantities and cost expectations for a 10x24 shed.
It does not include:
- Exact rafter angle calculations
- Detailed wall framing layouts
- Header engineering details
- Precise overhang measurements
- Optimized cut lists
- Printable construction diagrams
On long structures, layout errors can waste significant material and time.
Detailed blueprints with exact measurements, framing layouts, and printable cut sheets simplify construction, reduce waste, and help ensure structural accuracy.
For a one-time build, complete plans typically save time and money by preventing mistakes and rework.